Seal 'N Lock

Seal'N Lock Natural Luster 5 Gallon 01-NL5

$210.99
$210.99
Sold out

Natural Luster

Natural Luster® paver sealer from Seal ‘n Lock is a modified acrylic urethane sealer for brick pavers (with an algae and mold inhibitor) that penetrates the pavers to provide a protective barrier with superior joint stabilization (no need for polymeric sand) resulting in a natural luster. Natural Luster® paver coating is user friendly and environmentally safe.

Natural Luster® is user friendly and environmentally safe.

All Seal ‘n Lock products are made of the most environmentally-friendly products available, and offer excellent weatherability, UV protection, and help prevent algae and mold. All of our cleaning and sealing products and specialty coatings are VOC compliant in all 50 states and exceeds all hardscape product manufacturer’s minimum standards guidelines.

Natural Luster® is available in 5-gallon Pails Only.

Natural Luster® Benefits:

  • Superior Joint Stabilization
  • Minimal toxic odor
  • Inhibits Algae & Mold Growth
  • Inhibits weed growth and ant mines
  • Modest Enhancement
  • Will not harm vegetation
  • No need for polymeric sand
  • UV Protection
  • Provides a Protective Barrier
  • Hot tire marking resistant
  • VOC compliant in all 50 states
  • One day process (No downtime)
  • It May be applied to a damp surface
  • User friendly and environmentally safe

Estimating Guide

Typically, the application rate will vary from 150 to 200 sq. ft. per gallon for this paver coating, although this rate will vary depending on the texture, absorption rate of the surface and the width of the paver joints.

Directions For Use

We recommend wearing protective goggles and latex gloves. For best results, apply Natural Luster® at temperatures between 60° F and 90° F. In cooler conditions, the sealer should be warmed to approximately 70° F. Do not apply if surface or ambient temperature s below 50°F. A test for compatibility, penetration and adhesion is recommended. If the temperature is going to drop below freezing (32° F) make sure the sealer has time to cure.

Mixing

Natural Luster® is designed to be diluted with 1 part water and 1 part sealer with a 2 coat system (flood coat and top coat). Natural Luster® requires mixing and stirring (2 minutes) prior to use.

Drying Time

Natural Luster® paver coating will normally dry in sunny areas within approximately 1 hour. Shaded areas, lower temperatures or high relative humidity will slow the drying process. The surface may be open to foot traffic in 24 hours and to vehicular traffic in 48 hours. To minimize tire marks, vehicles should not make sudden stops or tight turns.

Cleanup

  1. Immediately flush and agitate pump system after sealing with a mixture of 3 gallons water and 8 ounces of pine sol.
  2. Flush out the pump system with 5 gallons of fresh water.
  3. Pour two ounces of Pine Sol into one gallon of water, run through the pump system and leave in the pump until next application.  
  4. Always run water through the pump prior to the next application.

Notes

Pavers with high absorption rate will require additional top coats of sealer to provide a protective barrier and desired enhancement.

Natural Luster® is not intended for submerged surfaces.

Maintenance

Periodic washing of pavers with a mild detergent to keep the area clean is recommended.

DO NOT USE ACIDS:Gasoline, hydraulic fluids and motor oil spills should be removed from the surface of the pavers as soon as possible. We recommend that surfaces previously sealed with Natural Luster® should be cleaned and resealed every 3 years, depending on environmental exposure and traffic.
CAUTION:Too many coats of sealer may induce a slippery condition. May be slippery during the application if walked on. May cause skin and eye irritation. Do not take internally. Wear a mask while applying. All label directions should be read thoroughly before use.